Call Us Now
+86-15190367399
Drawing machine die polishing machine
It is mainly used in wire drawing machine dies
For flux cored wire drawing machine,copper coating machine dies
A. An overview
It is specially designed for polycrystalline die polishing. It is quick when the polishing scope is over 0.35MM, saving grinding time to improve efficiency. It has advantages of high processing efficiency, good quality and low noise. It can be able to shape or polish quickly on die, and quickly make the processing side to reach mirror. In particular, it plays a significant role for large-sized mold processing.
B. Technical parameters
Processing range (mm): 0.35-5.00
Power: 220V 50HZ
Maximum output power (W): 150
Transducer: Japanese nickel-chip inductive
Frequency (KHZ): 25
Die-seat speed (rpm / min): 180
Die-seat swing (time / min): 150
Swing angle: not less than 12 degrees (adjustable)
C.working principle and equipment constitutes
This machine uses ultrasonic high-speed vibration, and via the steel needle and abrasive to strike on the processed surface, grind processed surface to meet the needed shape and size. This equipment consists of ultrasonic generator, transducer and machine base.
(1) ultrasonic generator: ultrasonic generator is installed in a 450mm * 210mm * 410 mm iron box. Line uses automatic frequency tracking, correct automatically frequency of different steel needle to match each other, so as to achieve ultrasound output and shock effect.
(2) transducer: It is pure nickel film of water-cooling type with efficient transducer effect.The ultrasound can be converted into smooth ultrasound shock, using water cycle cooling, and has the characteristic of low noise.
(3) Machine base: Table can be rotated and can swing the machine base forward and backward. With a spring installed inside table, you can move it up and down, and it can adjust the pressure, swing it before and after by eccentric wheel and pulley. The swing margin is about 12 degrees. The platform was installed in the L-plate and can correct center to ensure die non-deformation and roundness in polishing process. The transducer is installed on a pair of board after the column which can be moved up and down.
Drawing machine die polishing machine
It is mainly used in wire drawing machine dies
For flux cored wire drawing machine,copper coating machine dies
A. An overview
It is specially designed for polycrystalline die polishing. It is quick when the polishing scope is over 0.35MM, saving grinding time to improve efficiency. It has advantages of high processing efficiency, good quality and low noise. It can be able to shape or polish quickly on die, and quickly make the processing side to reach mirror. In particular, it plays a significant role for large-sized mold processing.
B. Technical parameters
Processing range (mm): 0.35-5.00
Power: 220V 50HZ
Maximum output power (W): 150
Transducer: Japanese nickel-chip inductive
Frequency (KHZ): 25
Die-seat speed (rpm / min): 180
Die-seat swing (time / min): 150
Swing angle: not less than 12 degrees (adjustable)
C.working principle and equipment constitutes
This machine uses ultrasonic high-speed vibration, and via the steel needle and abrasive to strike on the processed surface, grind processed surface to meet the needed shape and size. This equipment consists of ultrasonic generator, transducer and machine base.
(1) ultrasonic generator: ultrasonic generator is installed in a 450mm * 210mm * 410 mm iron box. Line uses automatic frequency tracking, correct automatically frequency of different steel needle to match each other, so as to achieve ultrasound output and shock effect.
(2) transducer: It is pure nickel film of water-cooling type with efficient transducer effect.The ultrasound can be converted into smooth ultrasound shock, using water cycle cooling, and has the characteristic of low noise.
(3) Machine base: Table can be rotated and can swing the machine base forward and backward. With a spring installed inside table, you can move it up and down, and it can adjust the pressure, swing it before and after by eccentric wheel and pulley. The swing margin is about 12 degrees. The platform was installed in the L-plate and can correct center to ensure die non-deformation and roundness in polishing process. The transducer is installed on a pair of board after the column which can be moved up and down.
