Call Us Now
+86-15190367399
WANYI
| Quantity: | |
|---|---|
Steel strip rewinding machine
FD1200+GZL00 dancer+SD800 Strip rewinding machine
Product model, composition and name
1. Product name: FD1200+GZL00+SD800 Spool take up machine
2. Product composition: FD1200 vertical passive pay-off machine + GZL00 Support rack + SD800 Spool take up machine
II.Application scope
This set is mainly used for the rewinding of steel belts.
III.Main technical parameters
1. Steel belt width (mm): 14
2. Pay-off motor power: Passive type (un-powered type)
3. Take-up motor power: 11KW
4. Winding displacement form: Ball screw winding displacement
5. Tension control: Sensor-controlled tension arm
6. Take-up speed (m/min): 4m/s
7. Take-up spool diameter (mm): ￠800
8. Air supply: 0.5-0.6Mpa, clean and dry air source for oil mist removal
9. Braking time: Normal braking≤60S
Quick braking≤10S
Emergency braking≤3S
IV.Main working principle:FD1200 vertical passive pay-off machine machine: Place the steel belt cut and coiled in the last process on the vertical passive pay-off machine by driving or a special sling. At this moment, the expansion sleeve is in an expansion & tension state. Put the steel belt in the expansion sleeve. Then use a special spanner to loosen the expansion sleeve to cause the expansion sleeve to tightly enclose the steel belt. GZL00 Support rack: Pull out the steel belt from the vertical passive pay-off machine, and allow it to enter the second group of horizontal guide rollers by way of the first group of horizontal guide rollers.
SD800 Spool take up machine: The steel belt from the roller support is pulled through the well-shaped guide roller and wire-pressing guide roller, and then it is wrapped around the spool. At this moment, start the device, gradually from a low speed to a normal working state. Use the tension arm to control the pay-off speed.
Steel strip rewinding machine
FD1200+GZL00 dancer+SD800 Strip rewinding machine
Product model, composition and name
1. Product name: FD1200+GZL00+SD800 Spool take up machine
2. Product composition: FD1200 vertical passive pay-off machine + GZL00 Support rack + SD800 Spool take up machine
II.Application scope
This set is mainly used for the rewinding of steel belts.
III.Main technical parameters
1. Steel belt width (mm): 14
2. Pay-off motor power: Passive type (un-powered type)
3. Take-up motor power: 11KW
4. Winding displacement form: Ball screw winding displacement
5. Tension control: Sensor-controlled tension arm
6. Take-up speed (m/min): 4m/s
7. Take-up spool diameter (mm): ￠800
8. Air supply: 0.5-0.6Mpa, clean and dry air source for oil mist removal
9. Braking time: Normal braking≤60S
Quick braking≤10S
Emergency braking≤3S
IV.Main working principle:FD1200 vertical passive pay-off machine machine: Place the steel belt cut and coiled in the last process on the vertical passive pay-off machine by driving or a special sling. At this moment, the expansion sleeve is in an expansion & tension state. Put the steel belt in the expansion sleeve. Then use a special spanner to loosen the expansion sleeve to cause the expansion sleeve to tightly enclose the steel belt. GZL00 Support rack: Pull out the steel belt from the vertical passive pay-off machine, and allow it to enter the second group of horizontal guide rollers by way of the first group of horizontal guide rollers.
SD800 Spool take up machine: The steel belt from the roller support is pulled through the well-shaped guide roller and wire-pressing guide roller, and then it is wrapped around the spool. At this moment, start the device, gradually from a low speed to a normal working state. Use the tension arm to control the pay-off speed.
